产品中心

Hn electronic
Home > 产品中心 > 贴片式蜂鸣器  .

MLT-1030

  • 产品描述
  • 其它

A. SCOPE 
This specification applies Piezo buzzer, MLT-1030

B. SPECIFICATION

No.

Item

Unit

Specification

Condition

1

Oscillation Frequency

Hz

5200

Square Wave

2

Operating Voltage

Vp-p

1~25

 

3

Rated Voltage

Vp-p

5

 

4

Current Consumption

mA

MAX. 3

at Rated Voltage

5

Sound Pressure Level

dB

MIN. 75

at 10cm at Rated Voltage

6

Electrostatic Capacity

pF

11000±30%

at 100Hz 1V

7

Operating Temperature

-20~ +70

 

8

Storage Temperature

-30 ~ +80

 

9

Dimension

mm

Φ10 x H3.1

See appearance drawing

10

Weight (MAX)

gram

0.3

 

11

Housing Material

 

LCP( Black )

 

12

Leading Pin

 

Plated Brass(Au)

See appearance drawing

13

Environmental  
Protection Regulation

 

 RoHS

 

 

C. APPEARANCE DRAWING  
 
Tol : ± 0.3     Unit: mm


D.TESTING METHOD    
Standard Measurement conditions
Temperature:25±2℃  Humidity:45-65%

Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the measuring instruments shown below
 
In the measuring test, buzzer is placed as follows:
 

E. Typical Frequency Response Curve

F.Soldering Condition
(1)Recommendable reflow soldering condition is as follows
(Reflow soldering is twice)
Note:It is requested that reflow soldering should be executed after heat of product goes down to normal.

Heat resistant line
(Used when heat resistant reliability test is performed)
(2)Manual soldering
Manual soldering temperature 350 ℃ within 5 sec. 

G. RELIABILITY TEST

NO.

ITEM

TEST CONDITION AND REQUIREMENT

1

High Temperature
Test (Storage)

After being placed in a chamber with 802℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

2

Low Temperature
Test (Storage)

After being Placed in a chamber with -302℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

3

Humidity Test

After being Placed in a chamber with 90-95% R.H. at 402℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

4

Temperature Cycle
Test

The part shall be subjected to 5 cycles. One cycle shall be consist of:

Allowable variation of SPL after test: 10dB.

5

Drop Test

Drop on a hard wood board of 4cm thick, any directions ,6 times, at the height of 75cm .
Allowable variation of SPL after test: 10dB.

6

Vibration Test

After being applied vibration of amplitude of 1.5mm with 10 to 55 Hz band of vibration frequency to each of 3 perpendicular directions for 2 hours .
Allowable variation of SPL after test: 10dB.

7

Solderability
Test

Lead terminals are immersed in rosin for 5 seconds and then immersed in solder bath of +3005℃ for 31 seconds .
90% min. lead terminals shall be wet with solder
(Except the edge of terminals).

8

Terminal Strength
Pulling Test

The force of 9.8N(1.0kg) is applied to each terminal in axial direction for 10 seconds.
No visible damage and cutting off.

TEST CONDITION.
Standard Test Condition              :      a) Temperature : +5 ~ +35℃  b) Humidity : 45-85%        c) Pressure : 860-1060mbar 
Judgment Test Condition             :      a) Temperature : +25 ± 2℃    b) Humidity : 60-70%        c) Pressure : 860-1060mbar 

H. PACKING STANDARD

在线客服

业务联系
业务联系
业务联系
重庆欢乐生肖彩票 重庆福彩欢乐生肖走势图 欢乐生肖开奖直播 重庆欢乐生肖开奖 重庆欢乐生肖期数 欢乐生肖福彩直播 欢乐生肖 金牛彩票 欢乐生肖开奖直播 欢乐生肖开奖直播